We have given you an entire week without any pictures of the NEW Hold cock & ball cage--but it's back!  (We sold so many of them at International Mr. Leather that frankly, we have more pictures of the Hold than we can shake a dick at!)  The Hold is gear essentials' kinky first-time entry into cock & ball cages.  It acts as a cockring and shaft ring--all in one piece of solid stainless steel gear!

As the pictures below will show, we really had a lot of fun with this new gear at IML.  In fact, we found that it created a lot of heat--as guys popped them on (to be fair--there was NO popping; these take a bit of concentration to lock on) they would be surrounded by a crowd of admirers.  Some couldn't resist the apparent magnetic pull drawing them in to touch...and sometimes more!


The NEW Hold Cock & Ball Cage by gear essentials Premiered at International Mr. Leather


You've asked for bigger and bolder and here it is!  The Hold cock ring is our widest with a bandwidth of 1.5" (38 mm) and is available in three interior diameters:  1 3/4" (44.5 mm), 1 7/8" (47.6 mm) and 2" (50.8 mm).  You can lock up your cock and balls and rock a wider cock ring yet allow your balls to drop through, hang free and not feel like they are pulled up to your chin.  Everything will be pointed in the right direction!


Hands Free?  Not Likely!  Try to Resist the Magnetic Pull of the HOLD Cock & Ball Cage!


That's right, the Hold will inspire all sorts of creative wrestling holds!  Heath likes to call this the 'mouth & palm' hold.  We looked it up on WWF but couldn't find it listed.  What is that all about?

It's a good thing it has a magnetic pull--the first time you put it on you will want a helping hand or two.  Putting it on for the first time can be a challenge.  Slip the larger half over your cock and balls and push it snugly against your pubes with the slotted side down.  Let your balls drop through the wide slot and slide the head of your dick through the outer ring.  Pull the two halves together so you can line up the screw with the hole (now there's a life theme for ya!)  Hand tighten the two screws until the Hold is firmly locked down.  (The two halves have to be aligned for the screws to go in smoothly.)  Based on our experience (and customer feedback), getting into The Hold gets much easier with practice!

Note that the band closest to your pubes is the wider of the two rings--this allows you to get most of your balls in the indentation (wide slot) before securing the outer ring to minimize the risk of pinching.  The outer ring tapers to a narrower opening which adds weight and acts as a shaft ring.  For some this gives an increased shaft pressure that they have never experienced before.  Like any ring, it restricts blood flow in your dick so your shaft gets even bigger.  Guys (and their partners) are loving it!


The Hold Gives a Grip that Hugs your Balls & Shaft...& Begs to Be Held 


Can You Jack with It?

You can but you will have a shorter stroke.  The ring is taking up 1.5" of the length of your shaft--fortunately, for most; the erogenous bits are closer to the other end of your dick so it's all good.  We found that it forced us to be creative and try some new techniques.  


Can You Fuck with It?

We have heard a couple of responses:

  • "No thanks, I want more depth to my fuck and this is cramping my style."
  • "I love it, the combination of cock ring and built in shaft ring made me HUGE and the fucking is fucking awesome!"
  • One IML customer stopped back to report that he took the outer ring off for fucking--this gave him the room he needed for the depth of thrust that he and his partner enjoy while the base ring gave him the support and fullness he likes.

You can do a lot with it--and you will get the attention you deserve!

gear essentials…Sex is Better here! ENJOY!


WHERE TO FIND IT:    The Hold Cock & Ball Cage:



(Photos by Jay Williams.)  


Written by Jay — July 07, 2014

Leave a comment

Please note: comments must be approved before they are published.